Sterling Silver Trophy Repair
Sterling silver trophy repaired
This sterling silver trophy (above) arrived with the trophy cup broken from the stem. The trophy cup was wrinkled, dented and very damaged especially at the bottom center of the cup where the silver was the thinnest. The base was crushed. The trophy also had a coating that was extremely difficult to remove. This was an expensive repair, and I should have charged twice as much.
In the photos below are two different sterling silver trophies. The dents were removed, cups made round handles reshaped to restore these trophies to their former glory.
Antique Silverplate Trophies
Vintage Trophy with Yellow Aged Lacquer and Broken Handle - Repaired & Refinished
This vintage trophy arrived with aged, and yellow lacquer. After the lacquer was removed you could see the original silver plate color. Then I spent a great deal of time rebuilding a section of the handle that was lost. Because I used sterling silver to rebuild the handle, the repair matched the silverplated finish. Finally, the handle was attached. Click here to view a step by step example of a trophy repair.
光棍影院手机里光棍影院手机里,韩国好看的三级韩国好看的三级Repair of Vintage Silverplate Athletic Trophy
This vintage silverplate athletic trophy from 1933 arrived broken where the trophy cup attaches to the base. One of the handles was also pulling off because the trophy cup was out of round. The silverplated white metal was very soft and thin so I created a tapered brass tubing for core support along with additional structural elements (not visible) to hold the cup upright. At the juncture of the cup to the base, I added a sterling silver wire to conceal and strengthen the solder joint. Then the silverplating was carefully polished. There was a lot of wear on the silverplating from a hard life and many previous repairs, however the final result is very rewarding. This trophy retains all its 84 years of character.
REPAIR OF 20TH CENTURY SILVERPLATE WATER PITCHER TROPHY
This silverplate water pitcher was a trophy. (Notice the screws below the feet in the right photo.) Unfortunately, the owner took it to a welder for repair and he melted two sections of the handle instantly. Taking silverplate or sterling to a welder is a mistake. A welding torch is too hot! Welders do not have the skill or tools for working on sterling and silverplate objects.
This water pitcher trophy is silverplate on a "white metal" that melts at a very low temperature. When the customer brought this water pitcher about a 1/2" at the top of the handle and about 1" at the bottom of the handle were missing. This is visible in the left photo. As you can see the handle was also hollow and very thin.
I reconstructed the handle with low temperature solder "carving the repaired area" to resemble my guess at the original shape. Fortunately, the silver plating was in good enough condition. The trophy looks good. (Right photo.)
SILVERPLATE TROPHy from 1930 restored with new silverplating
The silver plating on this trophy was worn down to the base metal and could not be polished. The photo (left) is the appearance of the trophy before silver plating.
New silverplating was necessary to restore the appearance. In the close-up photo ( upper left) you can see the fidelity of the trophy lettering is still in tact even with new silver plating.
I do not do silver plating but will take it to a local silver plating firm that does silver plating for my customers.
Look below for another trophy before and after silver plating.
Antique Athletic Trophy Before and After Silver Plating
This athletic trophy arrived, tarnished, bent and more. I was told that when they were kids 60 years ago, they set of a small fire in the trophy cup. Possibly this is why it seems to have a blistered appearance. The soft metal was easy to straighten and round the cup, Then it was silver plated.
Removing Lacquer from Trophies
GREVE TROPHY AIR RACE REMOVE LACQUER & polish
This Louis W. Greve Air Race Trophy was lacquered silverplate but the lacquer was starting to break down causing large areas of black tarnish. In addition, the lacquer was starting to yellow and discolor so that the trophy was no longer a brilliant silver color. The disadvantage of lacquer is that the customer can not polish the trophy themselves.
Removing the lacquer took hours and hours, the biggest challenge was getting it out of the detailed border design.
This trophy was truly magnificent historic example of an airplane trophy at 25" in height.
Removing old lacquer and polishing
These antique silverplate trophies had gold plated interiors but they arrived so dark and tarnished is was hard to tell how well they would turn out. The lacquer applied to the silverplate had yellowed and started to break down. In addition, two of the handles were broken.
First I removed the lacquer, repaired the handles and then polished both the inside and outside of the trophies. It was essential to be very careful so that I didn't polish through the plating. With this approach it was not necessary to replate the trophies saving the customer money. Most important, but the original gold plating in this deep rich yellow color would be extremely expensive and hard to replace. The trophies aren't perfect, but I think that when an object is 100 + year's old, it is part of its character to have a little wear.
White Metal Trophy Restoration
Antique Silverplate Trophy with Base
This antique silverplate trophy arrived broken and missing a part. The owner did not realize a part was missing because the trophy was previously repaired badly with a mishmash of epoxy, glue, putty and pitch along with 20th century trophy parts. It took hours & hours to remove all the various glues and previous attempts at repair. I did the best possible job to polish the remaining silverplating. The base was also repainted. The final result is a remarkable improvement.
Repair of antique or vintage trophies is outside of the skill for do-it-yourself, or a trophy shop. Glue never works on metal. The best thing about glue is the advertising. Period! Don't use glue to repair antique or vintage trophies.
Repair 100 YEAR OLD ANTIQUE SILVERPLATE TROPHY CUP
This 100 year old silverplate trophy cup arrived very badly damaged. The handles were completely ripped off leaving gabbing holes in the body of the cup. When the handles broke off they also damaged the top edge where the handles are attached. A 1/2" piece in the rim of the cup was missing.
The trophy cup was also crushed in half, and bent over on the stem so badly it wouldn't even stand up for the photo. (I had to start straightening it up just to take a picture.) The lid was also crushed in badly and the finial on the lid was broken off.
The trophy was a family heirloom. The customer wanted to keep it looking like it had "character." My goal was to repair the cup, handles and lid without replating. It was a lot of work but it looks fabulous!
Pewter trophy restoration
Vintage pewter trophy光棍影院手机里光棍影院手机里,韩国好看的三级韩国好看的三级
This trophy arrived with dents in the side, the trophy cup was out of round and the lid was dented so it no longer fit together. The most significant damage was that the base was crushed in and down in the middle, and the top was crushed. The trophy cup was also broken off the base. In the photos above you can see the damage before restoration and after it was repaired and polished.
Repairing Figurative Athletic Trophies
Spalding 1928 Baseball trophy
This Spalding 1928 Baseball trophy arrived with the back ankle broken, forward leg broken below the knee and the baseball base broken. At some time in its previous life, it had been glued back together. (Never use glue for repairing metal! It won’t work.) It probably took me longer to take off the glue, than solder the repairs. Though I have seen this described as white metal, I think it is lead as it soldered easily and it is very heavy. The owner decided not to remove the aging finish which I think is a yellowed lacquer on silverplate. The repairs were painted to match the current finish.
The customer said, The trophy “arrived today safely and looks fantastic. Thanks for what you did to preserve a trophy I had given up on.”
Athletic Figure Field Event Track Trophy
Athletic figure trophies are very vulnerable to breaking. The trophies are very heavy, yet often balanced with all the weight on one leg.
This running figure arrived with the leg broken at the hip and a poorly done repair at the foot. In addition, there was a bad repair with glue in an attempt to attach the metal base to the pedestal.
It took hours and hours to do this repair. Inside the leg I added some brass tubing to strengthen the repair on the inside. The repair solder is then sculpted to match the figurative details including the fabric of the athletic trunks. As a final finish I covered the repair with metallic leaf and a little diluted paint to age the metal leaf.
Mid-20th century Athletic trophy
This mid-century trophy was 21" tall. The figurines represented football, tennis, track, swimming, baseball and basketball.
When the customer brought in this trophy four of the athletic figurines were broken at the ankles. The athletic figures were made from lead so they were relatively easy to repair. I think they were originally brass plated, so I painted the repair a similar color.
How did the trophy figurines get broken? It seems that the trophy was shipped as one unit. It is surprising that more of the figures weren't broken as the trophy was very heavy and the figures were fragile.
If you ever have to ship a trophy with this type of athletic figures, disassemble it completely, and protect each figure in either bubble wrap or better yet, a small box.
Pot Metal Athletic Figure trophies光棍影院手机里光棍影院手机里,韩国好看的三级韩国好看的三级
Vintage Athletic Figure Basketball Trophies
This group of basketball trophies are an excellent example of repairing figurative pot metal trophies. The pot metal is usually very brittle and difficult to solder. They are always difficult to solder. Usually, I paint or apply metallic leaf to conceal the repair. Repairs on the trophy figures below start at $250 and up. Glue will not repair these trophies, there is nothing good about glue except the advertising.
ATHLETIC TROPHY FIGURES often break at the ankles
Vintage Athletic Trophies are very vulnerable to breaking at the ankles. The figures are usually pot metal making them very heavy, yet the metal is not strong and the metal is very brittle. This wrestler trophy and the football player trophy both broke their legs at the ankles. After the repair I painted the repair to match the worn vintage plating. The repair is completely invisible.
Athletic Runner Trophy Broken and Repaired
The running figure trophy from 1987 was broken at the base. The metal did not want to solder, but I kept trying because it had great sentimental value to its owner. It took hours to repair and then I used a metallic imitation gold leaf to conceal the repair.
Baseball trophy repaired
This 1949 Baseball Trophy arrived with damage to the athletic figure and the plastic base was badly broken. It's humble origins make repair all the more challenging, but I did the best I could to bring this trophy back to life.
The front bill on the baseball hat was rebuilt; the plastic base was glued back together and the plastic trophy base was carefully polished; the front label was polished and lacquered. All the glue from previous repairs was removed.
The customer said, "I got home today from traveling for the holidays and found the trophy you restored. I am speechless as I look at it. The work you did was beyond my expectation. It looks wonderful."